MODEL NUMBER | 9510-50 | 9510-75 | 9510-100 | 9510-200 | 9510-300 | 9510-400 | 9510-500 | 9510-1000 | 9510-1200 |
Description | 50kW | 75kW | 100kW | (Only 100kW cabinet can support parallel expansion up to 1.2 MW3) |
AC Output Ratings |
Operating Modes | 4-Quadrant with Programmable Voltage (CV), Power Amplifier (PHIL), Optional AC Load |
Output Configurations | 3 independent set per channel 3 x 1Φ (AC or DC), 2Φ + 1Φ (AC or DC), or 3Φ AC outputs |
Power, Max (1Φ or 3Φ) | 50kW/118kVA | 75kW/177kVA | 100kW/236kVA | 200kW/472kVA | 300kW/708kVA | 400kW/945kVA | 500kW/1181kVA | 1000kW/2362kVA | 1200kW/2835kVA |
Current Ranges (RMS per Φ) | 25, 112.5 A | 50, 168 A | 50, 225 A | 100, 450 A | 150, 675 A | 200, 900 A | 250, 1125 A | 500, 2250 A | 600, 2700 A |
Current Ranges (RMS 1Φ Mode) | 75, 337.5 A | 150, 506 A | 150, 675 A | 300, 1350 A | 450, 2025 A | 600, 2700 A | 750, 3375 A | 1500, 6750 A | 1800, 8100 A |
Frequency | 30 – 120Hz (10 mHz resolution) |
Voltage Ranges | 10 - 175, 10 - 350VRMS L-N (Split Phase 10-125, 20-250V Max) |
Voltage Accuracy | ± 0.1% F.S. |
Programming Resolution | 0.01V |
Load Regulation | ± 0.02% |
Distortion (THD)1 | 0.45% (Typical) 0.65% (Max)<70hz no="" load="" to="" full="">70Hz no load to full load |
Slew Rate | 1V/μS (10% to 90% measured at 90 degree turn-on into resistive load) |
Waveforms | Sine, n-Step Sine, Triangle, Clipped-Sine, Arbitrary (user defined) |
Phase Angle Control | 0 to 359 degrees / 0.1 degree resolution |
DC Output Ratings |
Operating Modes | DC Constant Voltage (CV), Constant Current (CC), Constant Power (CP), Power Amplifier (PHIL), Optional DC Load |
Power Max (1ch or 3ch) | 50 kW | 75 kW | 100 kW | 200 kW | 300 kW | 400 kW | 500 kW | 1000 kW | 1200 kW |
Current Ranges (Per Ch.) | 25, 100 A | 50, 150 A | 50, 200 A | 100, 400 A | 150, 600 A | 200, 800 A | 250, 1000 A | 500, 2000 A | 600, 2400 A |
Current Ranges (1 Ch.) | 75, 300 A | 150, 450 A | 150, 600 A | 300, 1200 A | 450, 2400 A | 600, 2400 A | 750, 3000 A | 1500, 6000 A | 1800, 7200 A |
Voltage Ranges | 10 - 200, 10 - 400 VDC |
Ripple | < 400mV RMS (into resistive load) |
Power Amplifier Mode |
Control Method2 | Analog Input ±10V PK-PK amplified to ±247.5V PK-PK (low range) and ±495V PK-PK (high range) |
Latency (input-output) | 50 uS typical |
AC & DC Measurements |
Peak Voltage | 406V / 724V RMS |
Accuracy | 0.1% Reading + 0.1% F.S. (AC RMS or DC) |
Resolution | 0.005% F.S. |
Peak Current (per Ch.) | 167, 500A per channel |
Accuracy | 0.1% Reading + 0.1% F.S. (AC RMS or DC) |
Resolution | 0.005% F.S. |
Peak Power | V Range x I Range |
Accuracy (kW or kVA) | 0.1% Reading + 0.1% F.S. |
Resolution | 0.005% F.S. |
Additional Measurements | Energy (Ah, kWh, kVAh), AC Crest Factor, AC Power Factor, True Power (P), Reactive Power (Q), Waveform Capture |
Waveform Digitizer |
Data Acquisition | Output Voltage AND Current | Aperture Time | 1 cycle to 64s |
Sample Rate | 125 k Samples / sec | Accuracy | 0.5% Range |
Memory Depth | 64k Samples (V & I per Φ) |
Control |
Local User Interface | Built-in Touch-Panel and PC-Based software tools including graphical user interface |
External System Comm | LAN (Ethernet) supporting SCPI |
Drivers | NI-Compliant LabVIEW Drivers |
Analog Current Monitor | [-10V, +10V] corresponds to ±Full Measurement Scale |
Analog Voltage Monitor | [-10V, +10V] corresponds to ±Full Measurement Scale |
Safety |
Isolation | Facility to Chassis – 1000V, Output to Chassis – 1000V, Output to Output Internal Isolation – 2000V |
Module Protection | Self-protecting for over-voltage, over-current, over-power, and over-temperature |
Physical | Emergency Stop and external Inter-Lock |
Programmable Safety Limits | Min/Max Voltage, Current (per direction), and Power (per direction) with separate limits and time delay values |
Watchdog Timer | Continuously monitors control communications |
Physical |
Connectors | 2 x ½ inch stud terminals per channel (Total of six) + Ground |
Cabinet Dimensions (HxWxD) | 78” x 28” x 39″ / 1980mm x 712mm x 990mm |
Cabinet Weight | 1000lbs/454kg for 50kW cabinet; 1200lbs/545kg (for 75kW and 100kW cabinet) |
Operating Temperature | 5 - 35°C (up to 95% RH non-condensing) |
Input Power (Single 100kW Cabinet) |
Voltage | Universal Input – 380V to 480V ± 10% (L-L, 3 Phase, 50/60Hz). Output Power reduced to 90kW below 360VAC input. |
Efficiency/Power Factor | Efficiency: > 90% typical (>92% at full power), Power Factor: > 0.95 typical (> 0.99 at full power) |
Current per Φ | 168A@380V, 144A@400V, 134A@480V |
